JH25系列開式雙點固定臺壓力機特點及標準配置
- 時間：2014-09-24作者：東莞市明浩通機械技術有限公司瀏覽：6643
特點 Characteristics
1、超大工作臺面，適應大面積薄板沖壓及自動化級進模生產，工作效率高。
1、Extra large worktable, suitable for great area sheet metal pressing and automatic step molding production, high working efficiency.
2、優質鋼板焊接機身，提高了機床強度和剛度。
Steel welded body enhancing the intensity and rigidity of the machine.
3、大齒輪、齒輪軸精密研磨，機床工作噪音低，運行平穩。
Precisely grinded rack wheel and wheel shaft, low machine operation noise and stable operation.
4、采用干式或濕式氣動摩擦離合－制動器，動作靈敏。
Adoption of dry or wet pneumatic frictional clutch-detent, the movements are sensitive.
5、采用雙曲軸逆向傳動，同步性好，抗偏載能力強。
Adoption of dual-crooked shaft converse transmission, providing excellent synchronization and strong anti carry-deflection capability.
6、滑塊采用六面矩形導軌，導向好，精度高。
Slide blocks with six-sidedrectangle gui derail, the guidance is excellent and the precisions are pinpointed.
7、無級調整電機裝置，適應不同沖壓件工藝要求。
Stepless gearings motor or device, fitting the craftsmanship of different pressing parts.
標準配置 Standard accessories
| 1、液壓超負荷保護裝置。 | Hydraulic over loading protection system. |
| 2、自動潤滑裝置。 | Automatic lubricating system. |
| 3、裝模高度電動調節裝置。 | Mould installation height adjustment device. |
| 4、無極調速電機裝置。 | Stepless gearing electromotor device. |
| 5、數顯模高指示器。 | Digital display mould height indicator. |
| 6、滑塊及模具平衡裝置。 | Balance unit for slide block and mould. |
| 7、電子凸輪控制系統和移動電柜。 | Electronic cam controller system and movable electrical equipments control box. |
| 8、可移動雙手操作盒 | Movable operation box for both hands. |
| 9、空氣吹料裝置。 | Air power material blowing device. |
| 10、防震用橡墊。 | Shock resist rubber mat. |
選配配置 Optional accessories
| 1、氣囊式模墊裝置。 | Air bag mould mat device. |
| 2、光電式安全裝置。 | Photo electricity safety device. |
| 3、腳踏開關。 | Pedal power switch. |
| 4、自動送料輸出軸。 | Automation on feeding output shaft. |
| 5、自動送料機。 | Automatic feeding device. |
| 6、快速換模裝置。 | Papid mold displacing unit. |
特殊要求 Special Requirements
點擊圖片查看大圖
主要技術參數 Main technical parameter
| 型號/技術參數 Model/Technical parameters | JH25-110 | JH25-160 | JH25-200 | JH25-250 | JH25-315 | ||||||||
| L | S | L | S | L | S | L | S | L | S | ||||
| 滑塊公稱壓力(KN) Slide block nominal pressure(KN) | 1100 | 1600 | 2000 | 2500 | 3150 | ||||||||
| 能力發生位置（mm） Capacity engender position (mm) | 5/3 | 6/3.5 | 7/4 | 7/4 | 7/4 | ||||||||
| 滑塊行程（mm） Slide block stroke (mm) | 180/110 | 200/130 | 250/150 | 250/150 | 280/180 | ||||||||
| 行程次數 （S.P.M） Stroke frequency （S.P.M） | L | 35-65 | 30-55 | 25-45 | 25-40 | 20-35 | |||||||
| S | 45-80 | 40-75 | 35-60 | 30-55 | 30-50 | ||||||||
| 最大封閉高度(mm) Max closing height(mm) | 400/435 | 450/485 | 500/550 | 550/600 | 550/600 | ||||||||
| 封閉高度調節量(mm) Closing height adjust measurement(mm) | 90 | 100 | 110 | 120 | 120 | ||||||||
| 滑塊中心距機身距離(mm) Distance between the center of the slide block and the body(mm) | 350 | 390 | 430 | 450 | 450 | ||||||||
| 工作臺至地面距離 (mm) Distance between the worktable and ground (mm) | 900 | 900 | 1000 | 14100 | 1100 | ||||||||
| 工作臺尺寸 (mm) Worktable measurements (mm) | 左右 Left Right | 1880 | 2040 | 2420 | 2700 | 2700 | |||||||
| 前后 Front Behind | 680 | 760 | 840 | 920 | 920 | ||||||||
| 滑塊底平面尺寸 (mm) Plane dimension of the slide block bottom (mm) | 左右 Left Right | 1360 | 1500 | 1850 | 2100 | 2100 | |||||||
| 前后 Front Behind | 520 | 580 | 650 | 700 | 700 | ||||||||
|
外形尺寸 (mm) Outline (mm) |
左右 Left Right | 2170 | 2340 | 2720 | 2970 | 2990 | |||||||
| 前后 Front Behind | 1790 | 2040 | 2500 | 2750 | 2950 | ||||||||
| 高 Height | 3130 | 3823 | 4050 | 4350 | 4360 | ||||||||
| 氣囊 Airbag | 頂出能力KN Propping capacity KN | 35×2 | 63×2 | 80×2 | 100×2 | 140×2 | |||||||
| 行程 mm Stroke mm | 70 | 80 | 90 | 100 | 100 | ||||||||
| 頂板面積 mm Propping plate acreage mm | 350×220×2組 | 410×220×2組 | 460×340×2組 | 540×420×2組 | 560×420×2組 | ||||||||
| 電動機功率（kw） Electromotor Power (kw) (Fixation/Variable) | 15 | 18.5 | 22 | 30 | 37 | ||||||||
| 重量（kg） Weight (kg) | 14500 | 21000 | 28500 | 38000 | 42500 | ||||||||
| 使用空氣壓力（Mpa） Air pressure used (Mpa) | 0.5 | 0.5 | 0.5 | 0.5 | 0.5 | ||||||||
技術參數如有變動，恕不另行通知！
- 推薦閱讀